Is 7075-T6 the Strongest Aluminum Plate? Grade and Temper Comparison

Dec 19, 2025

Leave a message

What Determines the Strength of an Aluminum Plate

The strength of a wrought aluminum plate depends on three things: the alloy system, the temper, and the product form. Copper and magnesium give solid-solution strengthening, zinc and magnesium in the 7xxx series form the precipitates that produce the highest strengths, and the temper controls how those precipitates are arranged in the matrix.

Plate is also not the same as sheet. Plate is normally supplied in thicknesses from about 6 mm upward, and thicker sections cool more slowly after quenching, which is one reason high-strength plate is often specified in a stress-relieved temper rather than a plain T6.

7075-T6 Properties and Registered Composition

7075 is an Al-Zn-Mg-Cu alloy. Its registered composition includes 5.1 to 6.1 percent zinc, 2.1 to 2.9 percent magnesium, 1.2 to 2.0 percent copper and 0.18 to 0.28 percent chromium, with silicon and iron each limited to 0.40 and 0.50 percent maximum and the balance aluminum. Density is 2.81 g/cm3.

ASTM B209 specifies that 7075-T6 plate shall have a minimum tensile strength of 572 MPa (83 ksi) and a minimum yield strength of 503 MPa (73 ksi). Within the 7xxx family those are the values that make T6 plate the benchmark for heavily stressed structural parts.

Grade / temper Min. tensile (MPa) Min. yield (MPa) Notes
7075-T6 572 503 Highest strength stocked plate grade
7075-T651 572 503 Stretched after aging for stability
2024-T3 483 345 Better fatigue and damage tolerance

How 7075-T651 Differs from 7075-T6

T651 indicates that the plate was stretched a controlled amount after solution heat treatment and aging, which relieves internal stress. The strength requirements are the same as T6, but the residual stress is lower, so distortion during heavy machining is reduced. For parts with tight flatness or concentricity requirements, T651 is the practical choice.

Parts that are machined from thick plate on both faces should always be assessed for residual stress, because removing material unbalances the internal stress field and the part can move after clamping is released, irrespective of temper.

Corrosion Behaviour and Welding Limits

7075 plate has lower resistance to stress-corrosion than the 5xxx or 6xxx families and is normally given a protective finish when used outdoors or in coastal air. Hard anodizing or a chemical conversion coating is applied, and cut edges and machined pockets should be treated as well as the faces.

Welding is not recommended for 7075. Fusion welding both destroys the temper and creates a crack-sensitive zone, so joints are made with rivets, bolts, bonded inserts or mechanical fasteners instead. Any design that requires welding is better served by a 6xxx or 5xxx alloy.

Choosing Between 7075-T6 and Other Grades

Select 7075-T6 when minimum weight and maximum strength dominate, as in aircraft fittings, tooling plates, racing components and high-load brackets. Select 2024-T3 when fatigue crack growth and damage tolerance are the driving requirements. Select 6061-T6 or 5083 when weldability, corrosion resistance and cost matter more than peak strength.

Frequently Asked Questions

Q: Is 7075-T6 the strongest aluminum plate that can be bought?
A: It is the strongest grade in regular commercial supply. A few 7xxx variants reach higher strength in specific product forms, but they are produced to narrow specifications and are not stocked as general-purpose plate.

Q: What are the minimum mechanical properties of 7075-T6?
A: ASTM B209 requires at least 572 MPa (83 ksi) tensile strength and 503 MPa (73 ksi) yield strength for 7075-T6 plate. Longitudinally and transversely tested values are both reported on the mill certificate.

Q: Can 7075-T6 plate be welded?
A: No, welding is strongly discouraged. It over-ages the material and produces a crack-prone joint, so riveted, bolted or bonded joints are used instead.

Q: Why specify 7075-T651 rather than 7075-T6?
A: T651 is stress-relieved by stretching, so a machined part is less likely to distort after material is removed. Strength is unchanged, and the extra processing is normally justified for precision parts.

Q: How should 7075-T6 be protected in a marine environment?
A: Specify a surface treatment such as hard anodizing or a chemical conversion coating, and treat cut edges and machined surfaces too. Bare 7075 has limited resistance to salt-laden air.

Q: Is 7075-T6 suitable for machining?
A: Yes, it machines well and produces a good surface finish at relatively high cutting speeds. Tool wear is lower than with many other high-strength alloys of comparable hardness.