1050 vs 1060 Perforated Aluminum Plate Comparison

Apr 23, 2025

Leave a message

Understanding 1050 and 1060 Perforated Aluminum Plate

Perforated aluminum plate is produced by punching a regular pattern of holes into aluminum sheet, creating a material used for ventilation, screening, filtering, decoration and acoustic control. 1050 and 1060 belong to the 1xxx series of commercially pure aluminum, which means they contain at least 99.5% and 99.6% aluminum respectively. Because neither alloy is strengthened by alloying elements, their behavior is defined by purity, temper and processing. The two grades look similar, but the small difference in purity has practical effects on strength, hole quality and corrosion resistance that matter when choosing a material.

Composition and Basic Properties

1050 has a minimum aluminum content of 99.5%, while 1060 has a minimum of 99.6%. The small difference reduces the amount of iron and silicon impurities in 1060. In practice, 1060 shows slightly higher tensile strength and hardness than 1050 in the same temper, while 1050 tends to be marginally more ductile. Typical tensile strength values for the common tempers are in the range of 110-150 MPa depending on temper and thickness, with 1060 at the upper end. Both alloys have excellent thermal and electrical conductivity, good corrosion resistance and very good formability, and both can be anodized or coated after perforation.

Behavior During Hole Punching

The ductility of the alloy directly influences how cleanly holes are produced. 1050 is softer and more forgiving during punching, which makes it a good fit for dense small-hole patterns, hole diameters of 3 mm or less, and special or irregular hole shapes where cracking risk is higher. 1060, being slightly stronger, needs a little more punch force but tends to give better control of hole diameter and edge quality, with tolerances in the region of plus or minus 0.1 mm achievable in production. For large holes of 5 mm and above, or for patterns with tight positional accuracy, 1060 is often the safer choice. Hole edges on 1050 may require deburring, while 1060 typically produces fewer burrs and can go directly to anodizing or powder coating.

Corrosion Resistance and Environmental Fit

Both alloys form a natural oxide film that protects against atmospheric corrosion. For indoor applications such as lamp filters, decorative partitions, acoustic panels and ventilation grilles, 1050 is perfectly adequate and more economical. Where the perforated plate will face outdoor conditions, humidity, rain or marine air, 1060 offers a measurable improvement: its higher purity gives better resistance to pitting, and the salt spray life is commonly considered about 20% longer than 1050 in equivalent tests. For outdoor equipment covers, machine guards and coastal installations, 1060 with anodized or PVDF-coated finish is the recommended combination.

Choosing the Right Grade and Specification

The decision between 1050 and 1060 perforated plate is mainly a question of duty and budget. Use 1050 when the plate is decorative or light-duty, the pattern is dense or intricate, and cost is a priority; typical thicknesses are 0.5-1.5 mm. Use 1060 when the plate carries mechanical load, must hold precise hole positions, or will be exposed to the weather; typical thicknesses are 2-6 mm. When ordering, specify alloy, temper, thickness, hole diameter, center spacing, open area percentage, sheet size and any required surface finish so that the supplier can produce the plate to the correct tooling.

FAQ

Is there any difference in hole quality between 1050 and 1060?

Yes, in practice 1060 produces slightly cleaner hole edges and better diameter control because of its marginally higher strength, while 1050 may need deburring for dense patterns.

Can 1050 perforated plate be used outdoors?

It can, and it performs reasonably in normal outdoor conditions, but 1060 with anodizing or coating is preferred where salt air, rain and long exposure are expected.

Which grade is better for small holes below 3 mm?

1050 is usually preferred for dense small-hole patterns because its higher ductility reduces the risk of cracking between closely spaced holes.

Do the two alloys cost much differently?

1050 is generally slightly more economical because it has a marginally lower purity requirement; the difference in material cost is small in most markets.

Can both alloys be anodized after perforation?

Yes, both anodize well. Anodizing after punching protects the hole edges as well as the surfaces and is recommended for outdoor use.