Aluminum Coil Alloy Sheet: 1xxx to 6xxx Series Guide

Jan 22, 2026

Leave a message

Key Takeaways

  • Aluminium coil and sheet cover the 1xxx (pure), 3xxx (Al-Mn), 5xxx (Al-Mg) and 6xxx (Al-Mg-Si) families; 6xxx is heat-treatable, the others are strengthened by work hardening.
  •  
  • Aluminium (2.7 g/cm3) is about 65% lighter than steel - its density is about 36% of steel's - cutting transport and handling weight.
  • O temper maximises formability; H-series tempers raise strength; 6xxx-T6 provides structural rigidity after heat treatment.
  • 5xxx alloys resist saltwater and are the marine-grade choice; 3xxx and 6xxx suit industrial and architectural use.
  •  

1. Alloy Families and Their Roles

Aluminium coil alloy sheet is a multi-alloy product available in the 1xxx, 3xxx, 5xxx and 6xxx series. 1xxx (99%+ pure aluminium) offers ductility and conductivity for packaging and heat exchangers; 3xxx (aluminium-manganese) balances strength and weldability for architecture and automotive trim; 5xxx (aluminium-magnesium) provides marine-grade corrosion resistance for coastal and offshore use; 6xxx (aluminium-magnesium-silicon) is heat-treatable and gives structural strength. The 1xxx, 3xxx and 5xxx series are non-heat-treatable and are strengthened mainly by cold working; the 6xxx series is strengthened by solution heat treatment and ageing (T6).

 

2. Core Traits

Lightweight: at 2.7 g/cm3, aluminium is about 65% lighter than steel (about 36% of steel's density), reducing transportation, handling and installation loads. Corrosion resistance: the natural oxide film protects against rust and moisture; 5xxx alloys resist saltwater and pitting, while 3xxx and 6xxx hold up in industrial and urban environments. Fabrication: aluminium sheet is easily cut, bent, stamped, welded and deep-drawn; 3xxx and 5xxx excel at welding, and 6xxx welds with appropriate fillers. Dimensional precision: tight tolerances (e.g. thickness tolerance about ±0.005 mm, flatness about 0.2 mm/m - typical supplier values) simplify mass production and assembly.

 

3. Typical Alloy Contents at a Glance

Series Main alloying elements Typical tempers Key strengths
1xxx 99%+ Al O, H14, H18 Ductility, conductivity, non-toxic
3xxx Mn about 1.0-1.5% O, H14, H18, H24 Balanced strength, weldability, formability
5xxx Mg about 2.6-3.6% (grade-dependent) O, H32, H34 Marine corrosion resistance, high strength
6xxx Mg + Si O, T6, T651 Heat-treatable strength, structural rigidity

Content ranges depend on the specific grade (for example 5052 has about 2.2-2.8% Mg, while 5083 reaches about 4.0-4.9%); confirm with the mill certificate.

 

4. Typical Dimensions and Applications

Cold-rolled coils 0.2-5.0 mm; hot-rolled coils 2.0-12.0 mm; cut sheets 0.3-12.0 mm; widths 1000-2000 mm with standard 1000x2000 and 1220x2440 mm sheets. Applications: packaging (cans, foil containers, utensils), architecture (cladding, roofing, curtain walls), automotive and transportation (body panels, trailer floors), marine (boat hulls and offshore platforms, e.g. 5754), industrial (storage tanks, ductwork), and agricultural machinery.

 

5. Fabrication Guidance

Bending: allow about 1x material thickness in O temper for tight bends and about 3x thickness in H-series for larger radii. Welding: choose compatible fillers - ER3003/ER4043 for 3xxx, ER5356/ER5183 for 5xxx, ER4043 for 6xxx; clean weld areas to remove oxides and oil; use low heat input to prevent warping. Surface treatment: anodizing (clear, black, bronze) or PVDF coatings extend outdoor life. Storage: keep coils vertical on racks, humidity about 60% or below, covered with moisture-proof film. Aluminium is fully recyclable; recycling uses about 5% of the energy of primary production (typical industry figure).

 

Frequently Asked Questions

Q1. Which aluminium series is marine-grade?
The 5xxx (Al-Mg) series, for example 5083 and 5754.

Q2. Is 6xxx weldable?
Yes - with ER4043 or similar fillers; the weld loses some T6 strength locally.

Q3. What temper for deep drawing?
O temper (fully annealed) for maximum formability.

Q4. How light is aluminium vs steel?
About 65% lighter; aluminium density is about 36% of steel's.

Aluminum Coil Alloy SheetAluminum Coil Alloy SheetAluminum Coil Alloy Sheet