7075 T651 vs 6061 T6 Aluminum: Properties and Selection Guide

Dec 11, 2025

Leave a message

Chemistry: Different Strengthening Systems

7075 is a heat-treatable Al-Zn-Mg-Cu alloy. EN 573-3 specifies 5.1-6.1% Zn, 2.1-2.9% Mg and 1.2-2.0% Cu, with Cr in the 0.18-0.28% range, Si up to 0.40%, Fe up to 0.50%, Mn up to 0.30% and Ti up to 0.20%. The zinc and copper content forms the MgZn2 and Al2CuMg precipitates that give the alloy its exceptional strength. 6061 sits in the Al-Mg-Si family: 0.8-1.2% Mg, 0.40-0.8% Si, 0.15-0.40% Cu and 0.04-0.35% Cr. Lower alloying additions but a cleaner, more weldable and more corrosion-resistant matrix.

Mechanical Properties Compared

Property 6061-T6 / T651 7075-T651
Tensile strength (typical) about 310 MPa about 570 MPa
Yield strength, 0.2% (typical) about 276 MPa about 500 MPa
Elongation (typical) about 10-12% about 11%
Hardness about 95 HB about 150 HB
Machinability good fair
Weldability good (filler 4043 / 5356) poor, generally not welded
Corrosion resistance very good moderate, needs protection

ASTM B209 is the general specification for plate of both alloys; 7075-T651 plate for aerospace use is additionally covered by AMS 4045, which fixes composition and mechanical acceptance limits for the 5.6Zn-2.5Mg-1.6Cu-0.23Cr composition.

Physical Properties

Property 6061-T6 7075-T651
Density 2.70 g/cm3 2.81 g/cm3
Elastic modulus about 69 GPa about 72 GPa
Typical thermal conductivity about 167 W/m.K about 130 W/m.K
Melting range 582-652 C 477-635 C

The closer atomic packing of the 7075 matrix also raises electrical resistivity modestly, which matters when the part doubles as a conductor or an EMI path.

Corrosion, Fatigue and Service Behaviour

6061 resists atmospheric, fresh-water and mild chemical attack without additional protection and is not prone to stress-corrosion cracking in normal tempers. 7075 has lower general corrosion resistance and, in some tempers, is susceptible to stress-corrosion cracking; service parts are protected by anodising or primer and are not used where sustained tensile stress acts in a wet or chloride-bearing environment. On the fatigue side, 7075 offers the higher fatigue strength at the same stress ratio, which is why it dominates highly loaded airframe fittings, while 6061 is chosen where load cycles are moderate and stiffness or corrosion resistance governs.

Selection Guidance

Use 7075-T651 when the design is strength- or weight-critical and the part is machined from solid in a protected environment: airframe fittings, moulds and dies, high-load brackets, racing components and defence hardware. Use 6061-T6 or T651 when the part is welded, anodised for appearance, exposed to weather or chemicals, or when a moderate strength level at lower cost and better machinability is sufficient: jigs, fixture plates, structural frames, marine fittings and general engineering components.

Frequently Asked Questions

Q: Is 7075-T651 twice as strong as 6061-T6?
A: In tension, yes - typical tensile strength is around 570 MPa against about 310 MPa - but the ratio is lower in fatigue and in stiffness, where the elastic moduli differ by only about 4%.

Q: Can 7075 be welded?
A: Generally not for structural service; the alloy is sensitive to hot cracking and heat-affected zone strength loss, so 7075 parts are mechanically fastened or bonded.

Q: Which alloy machines better?
A: 6061-T651 machines faster and leaves a better finish with less tool wear; 7075-T651 machines to a good finish but at lower cutting speeds and with more attention to chip evacuation.

Q: Does 7075-T651 need surface protection outdoors?
A: Yes. Anodising, chromate conversion or a primer system is applied to limit pitting and to reduce stress-corrosion risk.

Q: Which standard should the purchase order reference?
A: ASTM B209 for plate of either alloy, with AMS 4045 added when 7075-T651 plate is required for aerospace acceptance.