Overview of 7075-T6 Aluminum Plate
7075 is an aluminum-zinc-magnesium-copper alloy developed for applications where strength is critical and weight must stay low. In the T6 temper it reaches tensile strength around 83 ksi, or about 570 MPa, approaching the strength of some steels at one third of the weight. The alloy is widely selected for aerospace, defense and high-load mechanical components, where its fatigue performance, dimensional stability and machinability justify a higher material cost than general-purpose 6xxx alloys.
Chemical Composition
The nominal composition of 7075 includes 5.1-6.1% zinc, 2.1-2.9% magnesium, 1.2-2.0% copper and 0.18-0.28% chromium, with the balance aluminum. Zinc and magnesium form the strengthening precipitates during aging, while copper adds strength and chromium controls grain structure. The combination produces the highest strength of the conventional aerospace alloys, but it also makes the material more sensitive to stress corrosion than 5xxx or 6xxx grades, which is why temper selection and protective finishing are essential in service.
Key Mechanical Properties
In the T6 condition, 7075 plate typically shows tensile strength of 510-570 MPa, yield strength around 435-505 MPa and elongation of 6-11% depending on thickness. Hardness is approximately 150 HB. The alloy has excellent machinability, rated B by the Aluminum Association, producing smooth finishes and well-formed chips. Fatigue strength is outstanding for an aluminum alloy, which is why the grade dominates aircraft structure. The trade-offs are poor weldability, due to hot cracking risk, and moderate corrosion resistance that requires surface protection in humid or marine environments.
Typical Applications
In aerospace, 7075-T6 plate is used for aircraft fittings, airframe structures, wing skins and other high-load components where the strength-to-weight ratio pays off directly in fuel savings and payload. Defense applications include missile parts, military hardware and armored vehicle components. In mechanical engineering the alloy appears in gears, shafts, molds and tooling subjected to high stress, and in sports equipment such as high-performance bicycle frames and climbing hardware. In every case the material is chosen because a lighter part can carry the same load.
Temper Variations
The standard T6 temper offers maximum strength, while T651 adds controlled stretching for stress relief, improving resistance to stress corrosion cracking and reducing distortion during machining. The overaged T73 and T7351 tempers trade a small amount of strength for substantially better stress corrosion resistance, and they are specified for components that will see sustained tensile stress in corrosive environments. Specifying the correct temper for the service condition is as important as choosing the alloy itself.
Fabrication Considerations
Welding 7075 is generally not recommended because the heat-affected zone is prone to cracking; mechanical fastening and adhesive bonding are the standard joining methods. Machining is straightforward with carbide tooling at appropriate speeds. Because the alloy is susceptible to galvanic corrosion when coupled with dissimilar metals, fasteners and fittings should be insulated or coated, and anodizing or painting is advised for outdoor service. Plates should be stored flat in a dry environment to avoid distortion and surface damage.
FAQ
How strong is 7075-T6 aluminum?
7075-T6 has tensile strength around 83 ksi, about 570 MPa, which is among the highest of any commercial aluminum alloy.
Can 7075-T6 be welded?
Welding is generally not recommended because of hot cracking risk in the heat-affected zone; riveting, bolting and adhesive bonding are preferred.
What is the difference between T6 and T73?
T73 is an overaged temper with improved stress corrosion resistance at the cost of slightly lower strength, specified for corrosive service conditions.
Is 7075 corrosion resistant?
It has moderate corrosion resistance, better than 2xxx alloys but lower than 5xxx and 6xxx grades; anodizing or painting is recommended for wet environments.
What is 7075-T651?
T651 is the T6 temper with controlled stretching for stress relief, which improves resistance to stress corrosion and reduces machining distortion.
Where is 7075 plate most commonly used?
Aerospace structures, defense hardware, high-load mechanical parts and premium sports equipment where high strength at low weight is essential.
