What Is Aluminum Composite Plate? Structure, Fire Performance and Testing

Apr 27, 2025

Leave a message

What the Material Actually Is

Aluminum composite plate is a flat sandwich: two aluminium skins separated by a thermoplastic or mineral-filled core, bonded by adhesive film or by a hot-melt process on a continuous lamination line. A typical architectural panel is 4 mm total with 0.3 to 0.5 mm skins over a 3 mm core. The skins are usually 1100, 3003 or 3105 sheet with a coil-applied coating, and the core is either low-density polyethylene or a mineral-filled flame-retardant compound.

The skin performs the structural and weathering role. The core separates the skins so that the panel works as a stiff, flat plate at low weight, with a density roughly one third that of solid aluminium of the same thickness. That is the reason the material is used for large facade fields, soffits, canopies, signage and vehicle cladding.

Core Type and Fire Performance

Core chemistry is the single most important selection variable. A polyethylene core panel behaves poorly in a fire because the polymer contributes fuel, while a mineral-filled core limits heat release. Reaction to fire is classified under EN 13501-1, and the classification must always be taken from a test report on the specific construction supplied, because skin thickness, core formulation and coating all affect the result.

Item Typical value or class Note
Total thickness 3, 4, 5, 6 mm 4 mm dominates facade work
Skin thickness 0.2 to 0.5 mm 0.5 mm for exterior facades
Panel weight, 4 mm about 5.5 kg/m2 Roughly one third of solid aluminium
Surface burning, ASTM E84 Class A, flame spread index 0 to 25 Achievable with mineral-filled cores
Reaction to fire, EN 13501-1 Depends on core formulation Take from the report for that construction
Coating system Two-coat 70% PVDF, min 25 micrometre dry film Weathering performance to AAMA 2605

Standards and Test Methods

Product standards and test methods for composite panels fall into three groups. Product and general requirements for aluminium composite panels used in curtain walling are covered by GB/T 17748 in the Chinese standards system and by equivalent national specifications elsewhere. Bond integrity is measured by peel tests, notably ASTM D903 for peel strength of adhesive bonds, by the climbing drum peel method in ASTM D1781, and by tape adhesion tests in ASTM D3359 for coating adhesion. Fire and structural performance are assessed by ASTM E84 for surface burning characteristics and by ASTM E330/E330M for structural performance under uniform static air pressure difference.

When buying, ask for three documents together: a mill certificate for the skin alloy and temper, a peel strength test report on the production lot, and a fire classification report naming the exact construction. A panel certified on a 3 mm interior grade does not transfer that certification to a 4 mm exterior specification.

Fabrication and Installation Limits

Composite plate is routed and folded, not welded. The standard fabrication method cuts a groove through one skin and the core, leaving a thin hinge of the opposite skin which is then folded, and the resulting corner is closed with a structural or sealant adhesive. Bond strength at that routed fold line is the weak point of a finished cassette, so the routing depth and the adhesive used must be controlled to a written procedure.

Fixings must allow thermal movement. Aluminium expands about 23 x 10-6 per degree °C, so a 2 m panel changes length by roughly 0.9 mm across a 20 °C temperature swing. Panels are held on a sub-frame with fixed and sliding points, and the perimeter should be installed to the designed joint width rather than butted. Where the panel meets steel, isolating gaskets prevent galvanic corrosion at the fixing.

Where Composite Plate Is the Right Choice

Three duties suit the material: large flat fields where low weight and perfect flatness matter more than impact resistance; re-cladding and renovation where the existing structure cannot take additional dead load; and manufactured products such as vehicle bodies, signage and interior partitions where the sandwich can be cut and folded on standard equipment. For high-impact or high-load applications, solid aluminium sheet or a metal honeycomb panel performs better, and the composite panel should not be treated as an equivalent substitute.

Frequently Asked Questions

Q: What is the difference between aluminium composite panel and solid aluminium sheet?
A: The composite is a sandwich of two thin skins over a polymer or mineral core. It is much lighter and flatter at the same thickness, but it is not weldable and has lower impact resistance than solid sheet.

Q: Does the core type affect fire performance?
A: Yes, decisively. Mineral-filled flame-retardant cores can achieve a Class A flame spread index of 0 to 25 under ASTM E84; polyethylene cores cannot. The classification applies only to the tested construction.

Q: Which test measures the bond between skin and core?
A: Peel testing, mainly ASTM D903 for peel strength and ASTM D1781 for the climbing drum peel method. Coating adhesion is checked separately by ASTM D3359.

Q: How is a composite panel folded?
A: By routing a V-groove through one skin and the core and folding the remaining skin as a hinge, then closing the corner with adhesive. Routing depth is critical to the finished strength.

Q: Can composite panels be used in high-rise facades?
A: Only when the specified construction holds the required reaction-to-fire classification for that building type, and the classification report for that exact panel is available for approval.

Q: What coating should be specified for exterior panels?
A: A two-coat 70% PVDF system with a minimum 25 micrometre dry film thickness, validated to AAMA 2605 for colour and gloss retention.