What Mill Finish Means in Coil Supply
Mill finish describes the surface as it leaves the rolling mill: no coating, no anodizing, no mechanical brushing and no chemical brightening. The surface carries the natural oxide film that forms within minutes of rolling, which gives limited protection indoors and in mild environments and acts as a sound base for later anodizing, painting or laminating.
Coil is supplied in thicknesses from about 0.2 mm up to several millimetres, in tempers from annealed O and H111 through the strain-hardened H22, H24 and H32 conditions. Because the finish is not decorative, mill finish material is normally selected for structural, formed or fabricated parts where surface appearance is secondary to strength, formability and cost.
Chemistry of 5754 and 5083
Both grades are non-heat-treatable aluminium-magnesium alloys, so they gain strength from solid-solution hardening and from strain hardening rather than from precipitation. The difference between them is the magnesium and manganese content, which sets both the strength level and the way each grade responds to welding.
| Element | 5754 | 5083 |
|---|---|---|
| Magnesium | 2.6 to 3.6 percent | 4.0 to 4.9 percent |
| Manganese | 0.50 percent max | 0.40 to 1.00 percent |
| Chromium | 0.30 percent max | 0.05 to 0.25 percent |
The higher magnesium level in 5083 raises strength but also increases sensitivity to sensitisation, the precipitation of grain-boundary phases that can occur after prolonged exposure to elevated temperature. Material intended for service in hot environments is therefore specified carefully with respect to temperature limits.
Mechanical Properties in the O Temper
EN 485-2 specifies mechanical property ranges for plate, sheet and strip. For the O temper it gives a tensile strength range of 190 to 240 MPa for 5754 and 275 to 350 MPa for 5083, which reflects the two grades' different magnesium levels. Strain-hardened tempers such as 5754-H22 and 5083-H111 sit at intermediate levels, depending on the amount of cold reduction applied.
Both grades retain useful toughness at low temperature, which is one reason they are accepted for liquefied gas and refrigerated service, and both weld without loss of corrosion resistance in the weld zone when the correct filler is used.
Applications and Selection Logic
5754 mill finish coil is used for automotive inner panels, road tanker shells, general fabrication, chemical plant ducting and architectural components where a clean metallic surface is acceptable. Its lower strength is offset by excellent formability and by a smoother surface after forming than the higher-magnesium grade usually gives.
5083 mill finish coil is used for boat hulls, decking, superstructures, offshore fabrications, rail vehicle structures and pressure equipment. Its higher strength allows thinner sections for the same duty, which is important where weight is a design driver, and it performs well in saltwater without a coating as long as the design avoids crevices and stagnant water traps.
Where corrosion protection beyond the mill finish is needed, both grades anodize or paint well after appropriate pretreatment, and the mill surface is usually degreased and lightly etched before coating to give adhesion.
Frequently Asked Questions
Q: Is mill finish the same as bare aluminium?
A: Yes. Mill finish means the coil is supplied as rolled, with only the natural air-formed oxide film. It has not been anodized, painted or mechanically finished.
Q: Which grade is stronger, 5083 or 5754?
A: 5083 is stronger. EN 485-2 gives a tensile range of 275 to 350 MPa for 5083-O against 190 to 240 MPa for 5754-O, because 5083 contains more magnesium and manganese.
Q: Why is 5083 preferred for marine work?
A: It combines high strength with good resistance to saltwater corrosion and keeps its toughness at low temperature, so it suits hulls, decks and offshore structures where weight and durability both matter.
Q: Is mill finish coil suitable for outdoor use?
A: For mild inland conditions the natural oxide film is usually enough. In coastal, chemical or continuously wet service, an anodized or painted finish is specified instead.
Q: Can 5754 and 5083 be welded in the mill finish condition?
A: Yes, both weld readily. A 5xxx-series filler is normally used, and the joint area should be degreased and brushed before welding to avoid porosity and to keep corrosion resistance in the weld zone.
Q: What should be checked on the mill certificate for a coil?
A: Alloy and temper, the mechanical values tested in the delivered temper, dimensions and thickness tolerance, plus flatness and edge condition, since these determine how the coil performs on a forming line.
