H24 5086 Compass Aluminum Checkered Plate: Uses and Specs

Dec 18, 2025

Leave a message

What Is a 5086 Compass Checkered Plate?

A checkered plate, also called tread plate or diamond plate, is a flat aluminum plate with a raised pattern rolled or embossed on one surface. The compass pattern is one of the traditional raised designs, together with one-bar, five-bar and diamond patterns. The 5086 alloy is an aluminum-magnesium alloy with magnesium content of about 3.5% to 4.5%, which gives it higher strength than 5052 and excellent resistance to seawater corrosion, making it a common choice for marine and industrial flooring.

The H24 temper indicates a strain-hardened condition followed by partial annealing, which provides a good balance between strength and ductility for forming and installation.

Properties of 5086 in the H24 Temper

5086-H24 offers tensile strength in the range of roughly 240 to 300 MPa depending on thickness, with good elongation and formability. The alloy welds well using 5356 or 5183 filler and retains useful strength in the weld zone, which is important for ramps and platforms fabricated on site. Its corrosion resistance in salt water, industrial atmospheres and fresh water makes it suitable for coastal and process environments where painted steel would require constant maintenance.

The raised pattern increases friction on the surface, providing slip resistance in wet, oily or dusty conditions, while the aluminum base keeps the plate light and easy to handle.

Common Pattern Types

Checkered plates are available in several patterns. The diamond or flat-top pattern is the most widely used for general flooring. The compass pattern, with concentric rings, is specified where a non-directional slip-resistant surface is preferred. One-bar and five-bar patterns are common in specific regional markets and for vehicle flooring. The pattern depth and pitch follow product standards, and the pattern is present on one side only, leaving the reverse side flat for welding and mounting.

Available Specifications

5086 checkered plates are produced in thicknesses from about 1.5 mm to 8 mm, with widths up to 2000 mm and lengths up to 6000 mm or more. Standard tolerances follow EN 485-4 or ASTM B209 for thickness and flatness. The plates are supplied in mill finish as standard, and can be cut to size, drilled, punched, bent or welded by the fabricator. For architectural use, the surface can be brushed or clear anodized, although the raised pattern makes polishing more complex.

Applications

In construction, checkered plates are used for stair treads, walkways, loading docks, ramps and platform floors, where slip resistance and light weight are required. In marine environments, 5086 plates are used for decking, hatch covers, walkways and work platforms on ships and offshore structures. In transport, they floor trucks, trailers and toolboxes, and in industry they protect machine platforms and walkways in chemical plants and food processing facilities.

Fabrication and Handling

Checkered plate is cut with shears, saws or plasma, and edges are deburred to keep the raised pattern clean. Bending should be done with the pattern side in tension or compression as designed, and sharp tools prevent distortion of the raised features. When welding, clean the area around the joint to remove the oxide layer and use the correct filler. Store plates flat with protective film or interleaving to avoid scratching the pattern.

FAQ

What does H24 mean in 5086-H24?

H24 is a strain-hardened temper that has been partially annealed to reduce hardness while retaining part of the cold-worked strength, giving a balance of strength and formability.

Is 5086 checkered plate suitable for ship decks?

Yes. 5086 offers excellent seawater corrosion resistance and good weldability, and the raised pattern provides slip resistance, making it a standard choice for marine decks and platforms.

What is the difference between compass and diamond patterns?

Both are raised anti-slip patterns; the diamond pattern has a directional diamond grid, while the compass pattern uses concentric rings that look identical from every direction.

Can checkered plate be anodized?

Yes, but the raised pattern makes uniform anodizing more difficult, so most architectural use specifies brushed or mill finish. Clear anodizing is possible with careful process control.

Which filler is used to weld 5086?

5356 or 5183 filler rods are typical for welding 5086, providing matching corrosion resistance and strength in the weld.

What thickness of checkered plate is used for flooring?

Common flooring thicknesses are 2.5 mm to 6 mm, with heavier plates specified for vehicle and industrial traffic and lighter plates for walkways and architectural use.

Q: What is the composition of 5086 aluminum?
5086 is a marine-grade aluminium-magnesium alloy containing about 3.5-4.5% magnesium plus manganese and chromium, with no copper, which gives it high resistance to saltwater corrosion and good weldability while remaining a non-heat-treatable alloy.

Q: What thicknesses are typical for 5086 checkered plate?
Checkered plate is commonly supplied from 1.5 mm to 12 mm thick with a raised pattern height of about 0.5-0.8 mm, in standard widths of 1000, 1220, 1250 or 1500 mm and lengths up to 6000 mm, with custom cutting available.

Q: What is the tensile strength of 5086-H24 checkered plate?
In the H24 temper, 5086 plate typically offers a tensile strength of 290-365 MPa, a yield strength around 205 MPa and elongation of about 10-12%, values that comfortably exceed the requirements for ship decks, ramps and offshore walkways.

Q: How should 5086 checkered plate be cut without damaging the coating?
Plates are normally sheared, sawn or cut with a plasma or laser cutter; heavy cutting should avoid overheating the edge because temperatures above about 65°C can degrade the strain-hardened H24 temper, so water cooling and fast feed rates are recommended on large panels.

Q: Does 5086 checkered plate need painting for marine service?
Painting is optional: the natural oxide film already protects the alloy in seawater, but painting or anodizing is sometimes applied for appearance or to prevent galvanic interaction with steel fittings; in mixed-metal assemblies, insulating washers and coatings are used to avoid bimetallic corrosion.