Aluminium Foil for Battery Cathode Substrate: Alloy, Temper and Surface Requirements

Aug 14, 2025

Leave a message

The cathode substrate in a lithium-ion cell is a thin aluminium foil that carries two jobs simultaneously. It conducts electrons from the active material to the cell tab, and it acts as the mechanical carrier that holds the coated electrode together through coating, drying, calendering, slitting and winding. Because a single pinhole or a thickness step can cause a coating defect or a cell short, cathode foil is specified much more tightly than foil of the same gauge used in packaging.

Why Aluminium and Not Another Metal

Aluminium is used on the positive electrode because it forms a thin natural oxide layer that passivates the surface and keeps the metal stable across the operating potential of a cathode, roughly 3.0 to 4.5 V against lithium. Below about 1.5 V against lithium the same oxide layer is no longer stable and aluminium begins to alloy with lithium, which is why the negative electrode uses a copper substrate instead. This electrochemical window, not cost alone, is the reason the two electrodes use different collector metals.

Alloy Purity and Temper

Cathode foil is produced from high-purity grades such as 1060, 1070, 1085 and 1235, with the composition controlled to EN 573-3 for wrought aluminium. Purity matters because iron, copper and silicon-rich phases are cathodic relative to the aluminium matrix and act as initiation sites for pitting during cycling, so residual impurity levels are held well below those accepted in packaging foil. The temper is selected against the coating and winding process: H18 gives the highest strength for thin gauges and resists tension variations on the coating line, while softer tempers are chosen where the winding radius is tight and the foil must conform without cracking. Mechanical property requirements for the finished foil follow GB/T 36146, the Chinese standard for aluminium and aluminium alloy foil used in lithium-ion batteries.

Gauge, Mechanical Properties and Sheet Resistance

Mainstream cathode foil is supplied between 10 and 20 micron, with 12 to 15 micron covering most production cells. Gauge selection is a direct trade-off: thinner foil leaves more cell volume for active material and raises gravimetric energy density, but it also reduces the current-carrying cross-section and lowers the tension window on the coating line. Sheet resistance scales inversely with thickness, so a 12 micron aluminium foil at a resistivity of about 2.7 micro-ohm centimetre gives a sheet resistance of roughly 2.2 milliohm per square, and the resulting ohmic loss must be included in the cell design. Tensile strength and elongation are usually specified as a matched pair, since high strength without adequate elongation causes web breaks during winding.

Parameter Typical production range Process implication
Thickness 10 - 20 micron Energy density against web strength
Tensile strength 180 MPa and above in H18 Tension control on the coating line
Elongation 2 % and above Resistance to cracking at the winding radius
Surface roughness Ra 0.15 - 0.40 micron Slurry wetting and coating adhesion
Pinholes Zero accepted Direct short-circuit risk

Surface Condition, Slitting and Cleanliness

Coating adhesion depends on surface energy and topography, not on chemical bonding alone. The mill controls roughness through roll texture and pass schedule, and the converter must keep the surface free of rolling oil, dust and metallic debris. Slitting is a critical step because a burr left on the foil edge can pierce the separator during winding and create an internal short; burr height is therefore specified separately from thickness tolerance. Foil for electrode production is handled in dry rooms, since adsorbed moisture reacts with the electrolyte salt and generates hydrogen fluoride, which attacks the passivation layer and initiates pitting. Camber and flatness are also controlled because a wavy web causes coating thickness variation across the width.

Behaviour on the Coating Line

The cathode slurry, typically an active material with a conductive additive and a binder in a solvent, is applied to one or both sides of the foil and then dried. Drying subjects the web to thermal expansion and to solvent removal shrinkage, and the foil must accommodate that movement without wrinkling. Calendering then compresses the coating to a target density, applying high linear loads that the substrate must survive without elongation set. Adhesion of the dried coating to the foil is checked during qualification, and peel strength methods such as ASTM D903 are commonly adapted for electrode testing. Cell level verification of the finished electrode is carried out against IEC 62660 for traction cells and IEC 62133-2 for portable sealed cells.

Frequently Asked Questions

Q: What thickness of aluminium foil is used as a cathode substrate?
A: Most production cells use 12 to 15 micron foil, with the full commercial range spanning roughly 10 to 20 micron. Thinner gauges raise energy density but narrow the processing window.

Q: Which aluminium alloys are used for battery cathode foil?
A: High-purity grades such as 1060, 1070, 1085 and 1235 are standard. Low iron, copper and silicon content limits the number of initiation sites for pitting corrosion.

Q: Why is surface roughness specified on cathode foil?
A: Roughness controls how the slurry wets and anchors to the metal. Too smooth and the coating adhesion is weak; too rough and the coating weight becomes uneven across the electrode.

Q: Why are pinholes rejected in battery foil but tolerated in packaging foil?
A: A pinhole in an electrode substrate exposes bare metal that can contact the opposite electrode through the separator, creating an internal short circuit. Packaging foil can tolerate isolated pinholes because the polymer layers still provide a barrier.

Q: Which standard covers aluminium foil for lithium-ion batteries?
A: GB/T 36146 specifies aluminium and aluminium alloy foil for lithium-ion batteries in the Chinese system. Cell level requirements are covered by IEC 62660 for traction applications and IEC 62133-2 for portable cells.

Q: Why must cathode foil be handled in a dry room?
A: Adsorbed moisture reacts with the electrolyte salt to form hydrogen fluoride, which attacks the protective oxide layer on the aluminium and leads to pitting corrosion of the collector.