Aluminium Plate 20mm Thick: Alloys, Sizes and Selection

Dec 10, 2025

Leave a message

What Is a 20mm Aluminium Plate?

An aluminium plate is a flat-rolled product with a thickness above 6 mm, and 20 mm is a commonly requested heavy-gauge dimension for structural and industrial applications. It is produced by hot rolling of DC cast slabs, which gives a dense internal structure, uniform mechanical properties and good flatness. Plates are normally supplied in the H112 or annealed condition for the 5xxx series, in the T6 condition for the 6xxx series, and in a variety of tempers for the 1xxx and 3xxx series.

Because of its thickness, a 20 mm plate behaves differently from sheet: it is used mainly for load-bearing and wear-resistant parts rather than for bending and forming. Dimensional control, flatness and internal soundness therefore matter more than surface cosmetics in most applications.

Alloy Selection by Application

The 1xxx series, including 1050, 1060 and 1100, offers high purity, excellent corrosion resistance and good electrical conductivity, but relatively low strength. These grades are used where formability or conductivity is the priority and mechanical loads are modest.

The 3xxx series, led by 3003 and 3004, provides higher strength than pure aluminum with good corrosion resistance and weldability, and is a cost-effective choice for general fabrication, tanks and ducting.

The 5xxx series, especially 5052, 5083 and 5086, is the most common family for 20 mm plates in structural service. These aluminum-magnesium alloys combine medium to high strength with outstanding seawater and atmospheric corrosion resistance, and they are widely used in shipbuilding, offshore structures, pressure vessels, chemical tanks and transport equipment. Grades such as 5083 are specified in classification rules for marine construction.

The 6xxx series, notably 6061 and 6063, offers heat-treatable strength with good machinability. A 20 mm 6061-T6 plate is a standard choice for machine frames, jigs, moulds and general engineering parts, and anodizes well for architectural use.

The 8xxx series, including 8011 and 8079, is less common at 20 mm thickness and is mainly used for special packaging or capacitor applications.

Dimensional and Tolerance Considerations

20 mm plates are available in widths of 1000 mm, 1200 mm, 1250 mm, 1500 mm and wider, and in lengths from 2000 mm up to 6000 mm or more. Standard thickness tolerance for a 20 mm plate is typically plus or minus 0.5 mm under EN 485-4 or the corresponding tolerance class of ASTM B209, and flatness is controlled to suit laser cutting and machining. When the plate will be machined to a final thickness or used in a precision assembly, specify the tighter tolerance class and confirm the flatness requirement with the supplier.

Surface Treatment and Finishing

Mill finish is the standard and most economical surface for structural plate. For architectural or decorative use, the plate can be anodized, painted with PVDF or polyester coatings, brushed or polished. For marine and chemical service, the natural oxide layer of 5xxx alloys is usually sufficient, while 6xxx grades can be anodized to improve wear and corrosion performance. Protective film or paper interleaving is applied for surfaces that must arrive free of scratches.

Processing and Machining Notes

20 mm aluminium plate is normally cut by sawing, waterjet, plasma or laser cutting. Laser and waterjet produce the cleanest edges with minimal heat-affected zone, while plasma requires edge cleaning before welding. Drilling and tapping are straightforward with sharp carbide tooling and appropriate coolants. For welding, 5xxx plates use matching filler such as ER5356 or ER5183, while 6061-T6 uses ER4043 or ER5356 depending on strength requirements; heavy sections may need preheat and controlled interpass temperature to avoid cracking.

FAQ

Q: Which aluminium alloy is best for a 20mm plate in seawater?
5083 and 5086 are the standard marine grades. 5083 offers higher strength, while 5086 provides a good balance of strength and weldability; both are accepted by major classification societies for ship and offshore structures.

Q: Can a 20mm aluminium plate be bent or formed?
Bending is possible but requires powerful equipment and generous bend radii, typically several times the thickness. For heavily formed parts, a thinner sheet or a different product form is usually more economical.

Q: How much does a 20mm aluminium plate weigh?
Aluminium has a density of about 2.7 g/cm³, so a 20 mm plate weighs approximately 54 kg per square metre, about one third of the weight of a steel plate of the same size.

Q: Is 6061-T6 or 5083 the better choice for a machine frame?
6061-T6 is usually preferred for machine frames because of its higher strength, good machinability and stable dimensions after heat treatment. 5083 is chosen when the frame will face corrosive or marine environments.

Q: What is the standard delivery tolerance for 20mm plate?
Thickness tolerance is typically plus or minus 0.5 mm under EN 485-4 and the corresponding classes of ASTM B209; tighter tolerances are available on request for machined or precision components.

Q: Does the plate need certification for shipbuilding use?
Yes. For marine applications the plate should be supplied with mill certificates and, when required, classification society approval such as ABS, DNV, LR or CCS for the specific grade and temper.