Introduction to 5182 H48 Can End Coil
5182 H48 aluminum coil is specialized for the manufacture of food and beverage can ends, where rigidity, pressure resistance and consistent forming performance are essential. The alloy belongs to the 5xxx series with magnesium as the dominant alloying element, and the H48 temper represents full strain hardening without annealing for peak strength. This combination allows can manufacturers to use thinner gauges while maintaining durability, which reduces material cost and supports premium packaging designs.
Alloy Composition
5182 contains approximately 4.0-5.0% magnesium with small additions of manganese (0.20-0.60%) and chromium (0.05-0.25%) for stability. Iron, silicon, copper, zinc and titanium are controlled to low maximums to preserve surface quality and forming behavior. This composition provides the strength, corrosion resistance and fine-grained microstructure that can end production requires.
Core Properties
The H48 temper gives the coil exceptional tensile strength of 350-380 MPa and yield strength of 320-350 MPa, with elongation of at least 4% and hardness around 100-115 HV. This high rigidity lets can ends withstand internal pressure of up to about 75 psi for carbonated beverages and maintain lid integrity during retort processing. Despite its strength, the alloy retains good formability for stamping pull tabs, score lines, rivets and embossments at speeds up to 2,200 cans per minute without cracking. Its magnesium-rich oxide layer resists corrosion from acidic and alkaline food contents, and the material complies with food contact standards.
Technical Specifications
Thickness ranges from 0.17 mm to 0.32 mm: about 0.19-0.23 mm for standard beverage ends, 0.23-0.28 mm for retortable food lids and 0.28-0.32 mm for high-pressure specialty ends. Width ranges from 750 mm to 1650 mm, and coil weight from 700 kg to 3200 kg. Surface finish options include food-grade mill finish, pre-lacquered finishes and chemical conversion coating. The material is supplied to ASTM B209, EN 485-2 and GB/T 3880, with food contact compliance to FDA and EU requirements.
Applications
Primary applications are carbonated beverage can tops, non-carbonated beverage lids, high-acid juice closures, retortable food can lids and specialty high-pressure closures. The combination of pressure resistance, score line reliability and surface quality supports easy-open designs while preventing premature opening or leakage during transport and storage.
Processing and Quality Assurance
Uniform thickness within about ±0.004 mm and an ultra-smooth surface with roughness at or below 0.3 μm Ra ensure even stamping pressure and consistent lacquering, printing and adhesive bonding. Batch-to-batch consistency minimizes line setup adjustments and downtime. Every coil can be documented with material test reports, corrosion test results and mechanical property verification, supporting traceability for food packaging customers.
FAQ
Q1: Why is 5182 used instead of 5052 for can ends?
5182 provides higher strength in the H48 temper, allowing thinner gauges and better pressure resistance. 5052 is more formable but does not match the rigidity required for thin, high-speed can end stamping.
Q2: What thickness is used for carbonated beverage ends?
Common gauges are 0.19-0.23 mm for standard carbonated beverage can ends, with thicker material up to 0.32 mm for high-pressure or large-diameter closures.
Q3: Is 5182 H48 safe for direct food contact?
Yes. 5182 can end stock complies with food contact regulations including FDA and EU requirements, and is widely used for canned foods and beverages worldwide.
Q4: Can 5182 H48 coil be lacquered or printed?
Yes. The smooth, uniform surface accepts internal lacquers and external printing and coatings, and pre-lacquered or conversion-coated finishes can be supplied to improve adhesion and corrosion resistance.
Q5: How should can end coil be stored before use?
Store coils upright on a clean, dry surface, protected from moisture and physical damage. Keep protective wrapping intact until slitting or stamping to preserve surface quality.
