3003 H14 Embossed Aluminum Coil Plates: Texture and Strength

Jan 19, 2026

Leave a message

What Are 3003 H14 Embossed Aluminum Coil Plates

3003 H14 embossed aluminum coil plates are rolled aluminum sheets in the Al-Mn 3003 alloy, strain-hardened to the half-hard H14 temper and then passed through embossing rolls that press a raised, repeating pattern into the surface. The result is a material that keeps the corrosion resistance and formability of 3003 while gaining the anti-slip grip, rigidity and visual texture of an embossed finish. Coil plates can be supplied in continuous coil or as cut-to-length sheets, which makes them convenient for panel fabrication, stamping and roll forming lines.

Temper and Mechanical Characteristics

The H14 temper is a strain-hardened condition with a typical tensile strength range around 180-210 MPa and yield strength around 160-190 MPa, roughly 20 percent higher than annealed pure aluminum of the 1100 series. Elongation in a 50 mm gauge is typically 8 percent or more, so the material can still be bent, cut, welded and stamped without cracking. The half-hard state offers a practical balance: it is rigid enough to hold its shape under wind loads and light impact, yet formable enough for architectural panels, machine housings and vehicle flooring. With a density of about 2.71 g/cm3, the product keeps weight low compared with steel.

Embossing Patterns and Surface Options

Common patterns include diamond, stucco, hammered, line and custom designs produced from a customer drawing. Embossment depth typically ranges from 0.1 mm to 0.5 mm, and pattern repeat can be adjusted from 5 mm to 50 mm, allowing the texture to be tuned for traction, drainage or purely decorative effect. The raised texture improves grip underfoot, hides minor scratches and dents, and breaks up flat glare on large facades. Surface finishes available on embossed coil include mill finish, clear or colored anodizing, and polyester or PVDF coatings for outdoor color retention.

Typical Dimensions and Tolerances

Thickness is commonly supplied from 0.3 mm to 3.0 mm, with 0.5-1.5 mm typical for architectural use and 1.5-3.0 mm for industrial flooring and platforms. Width can be supplied from 100 mm to 2000 mm, and coil weights from 100 kg to 3000 kg with standard inner diameters of 508 mm or 610 mm. Flatness is typically held within 0.5 mm per meter so that installation stays uniform. Material is produced to recognized standards such as ASTM B209, EN 485-2 and GB/T 3880.

Key Applications

Architectural cladding and facades use embossed 3003 for its weather resistance and clean appearance. Flooring and walkways rely on the raised pattern for anti-slip traction in commercial kitchens, warehouses, stair treads and vehicle decks. Industrial panels, control enclosures and machine housings benefit from the dent and scratch resistance of the half-hard temper. In transportation, truck bed liners, trailer side panels and ship decking take advantage of the light weight and impact resistance. Interior design uses custom embossed patterns on wall panels, ceiling tiles and furniture accents, while HVAC and refrigeration applications use the increased surface area for heat dissipation.

Fabrication and Handling Guidance

Handle coils with soft slings and keep protective film in place until installation to avoid damaging the embossed texture. Store in a dry warehouse with relative humidity at or below 60 percent and never stack coils, because stacking can flatten the pattern. Cut with sharp shears, a laser or a CNC router so edges stay clean, and use a minimum bend radius of about four times the material thickness when forming. For welding, use ER3003 filler metal and keep heat input low to preserve temper and texture. Clean embossed surfaces with mild detergent and a soft brush, and avoid abrasive pads that would wear the finish.

FAQ

Is 3003 H14 embossed coil suitable for outdoor use?

Yes. 3003 provides good atmospheric corrosion resistance, and an anodized or PVDF-coated finish extends protection against UV, salt and industrial pollution for outdoor cladding and roofing elements.

What embossment depth is recommended for anti-slip flooring?

Deeper patterns around 0.3-0.5 mm generally give stronger grip for walkways and ramps, while shallower textures around 0.1-0.2 mm are preferred for decorative panels and interior cladding.

Can embossed coil be painted or anodized after forming?

Yes. The embossed surface accepts paint, anodizing and powder coating. Cleaning the surface first ensures adhesion, and the coating follows the texture without filling the pattern when applied at the recommended film thickness.

What is the difference between H14 and O temper embossed coil?

O temper is fully annealed and soft, so it forms very easily but dents readily. H14 is strain-hardened to roughly half the full-hard level, giving higher strength and rigidity while retaining enough formability for most panel work.

Does embossing affect the corrosion resistance of the plate?

No. The texture is pressed mechanically and does not change the alloy composition. In fact the pattern helps water drain off the surface, which can reduce water pooling and slow surface degradation in damp environments.

What thickness should I choose for a truck bed liner?

Most truck and trailer applications use 1.5-3.0 mm embossed plate so the floor resists denting from cargo while the pattern keeps the surface safe underfoot.

Frequently Asked Questions

Q: Which alloy grades does this article cover? The article covers 3003 in embossed aluminum sheet form, and it compares how the different alloying systems affect strength, corrosion resistance and formability.

Q: What surface pattern does this product have? The material carries a raised diamond pattern, which adds rigidity and traction to the sheet while the base alloy keeps its corrosion resistance and workability.

Q: How does the pattern provide anti-slip performance? The raised pattern increases friction underfoot, which is why embossed aluminum sheet is specified for floors, steps, ramps, platforms and vehicle decking.

Q: What thickness or gauge range is available? Typical gauges mentioned in the article range from 50 mm, 0.1 mm, 0.5 mm, 5 mm, which covers the common sheet, plate and foil requirements for this grade.

Q: What surface finishes can be supplied? Surface options covered in the article include mill finish, pvdf, polyester, stucco, brush, which suit everything from plain mill products to decorative and protective coatings.