5052 aluminum coil belongs to Al-Mg alloy,the use of a wide range, especially in the construction industry can not do without this alloy, is the most promising alloy.
5052 aluminum alloy coil contains 2.5 percent magnesium and 0.25 percent chromium. Its lightweight and corrosion-resistant properties make it suitable for the marine environment, aircraft fuel tanks, architecture, manufacturing, and more.
Technical Parameter of Al. 5052 Aluminum Coil
|
Alloy |
5052 |
|
Temper |
O ,H24 ,H32 ,H34 ,H112 |
|
Thickness (mm ) |
0.2-8.0 |
|
Width (mm ) |
100-2650 |
|
Length (mm ) |
c |
| Surface: | mill finish surface, bright, polished surface, with blue PVC films or paper-interleaved |
5052 Aluminum Coil Chemical Composition
| Alloy | Silicon | Iron | Copper | Manganese | Magnesium | Chromium | Zinc | Titanium | Other Elements | Aluminum | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 5052 | 0.25 | 0.4 | 0.1 | 0.1 | 2.2-2.8 | 0.15-0.35 | 0.1 | ... | Each | Total | |
| 0.05 | 0.15 | remainder | |||||||||
5052 H32 temper (¼ hard) Mechanical Properties
| Thickness (inch) | Yield Strength Min. (ksi) | Tensile Strength (ksi) | Elongation (%) | Bend Diameter | |
| Min. | Max. | Min. | Factor, N | ||
| 0.017 – 0.019 | 23 | 31 | 38 | 4 | 0 |
| 0.020 – 0.050 | 23 | 31 | 38 | 5 | 1 |
| 0.051– 0.113 | 23 | 31 | 38 | 7 | 2 |
| 0.114 – 0.249 | 23 | 31 | 38 | 9 | 3 |
| 0.250 – 0.499 | 23 | 31 | 38 | 11 | - |
| 0.500 – 2.000 | 23 | 31 | 38 | 12 | - |
What is 5052-H32 grade Aluminium?
Aluminium alloy 5052 in H32 temper has very good corrosion resistance to seawater and marine and industrial atmosphere. It also has very good weldability and good cold formability. It is a medium to high strength alloy with a strength slightly higher than 5251 and a medium to high fatigue strength.
What is the difference between 6061-T6 and 5052 H32 aluminum?
Are there specific applications where 6061-T6 or 5052-H32 excel over the other? 6061-T6 finds use in aerospace, bridges, transportation, and structural applications due to its strength, while 5052-H32 is favored for panels, enclosures, marine equipment, and medical devices where forming requirements are critical.
Can you weld 5052 H32 aluminum?
AA 5052 H32 is cold-rolled aluminium alloy having very high corrosion resistance with an industrial and marine environment, good formability, and good weldability out of other aluminium alloys and thus has been used for automotive and marine structural applications.
Is 5052 H32 aluminum bendable?
The best aluminum for sheet metal bending is the 5052-H32 alloy. This alloy has a good balance of strength, formability, and corrosion resistance, making it an ideal choice for sheet metal bending. It also has a high elongation percentage and good cold workability, which means it can be formed without cracking.
What is 5052-H32 equivalent to?
5052-H32 is one of the strongest heat-treatable sheet metals. It is relatively easier to bend and form. It has excellent weldability and high fatigue strength and is more elastic than 6061-T6. The tensile strength of this aluminum alloy is 33,000 psi, and its yield strength is 28,000 psi.
What is 5052 aluminum used for?
5052-H32 contains 2.5% magnesium. It is one of the highest strength alloys of the non-heat treatable grades. Common uses for this alloy include the manufacturing of electrical enclosures, marine parts, home appliances, food equipment, fuel tanks, storm shutters, refrigerators, aircraft tube, and fences.
Is 5052 cheaper than 6061?
Generally, 6061 aluminum, with its higher strength and heat-treatable properties, may be slightly more expensive than 5052 aluminum.
What is the price of aluminium 5052-H32?
Aluminum 5052 O, H32, 34, Sheets, Plates, Coils
₹260.00.
Is 5005 h34 better than 5052-H32?
5052 is stronger than 5005 and is used in applications requiring more structural integrity or impact resistance. 5052 has excellent corrosion resistance, medium static strength, medium to high fatigue strength, good weldability and very good corrosion resistance especially in marine applications.
What is the difference between aluminum 5052 O and 5052-H32?
Aluminum 5052-H32 is strong due to its special mix and treatment. The H32 label means it is made stronger using strain hardening. It is also softened a bit through annealing. This process makes it stronger than the annealed type, known as 5052-O, while still allowing some flexibility.
Which is stronger, 5052 or 6061?
5052 aluminum has the lowest strength among the three grades, with a tensile strength of around 220 MPa. 6061 aluminum offers moderate strength, with a tensile strength of around 310 MPa. 7075 aluminum is the strongest of the three, with a tensile strength of around 572 MPa.
What is the difference between 5454 h34 and 5052-H32?
They are both primarily alloyed with magnesium and have good formability. But 5052 has a slight advantage over 5454 aluminum in formability and resistance to marine corrosion. And 5454 is the better choice for applications that require higher strength and resistance to chemical corrosion.
3003 h14 Aluminum Coil Properties
3003 aluminum coil is commonly used 3000 series Al-Mn anti-rust alloy. So, 3003-h14 aluminium coil has good corrosion resistance, weldability, machinability, formability, surface treatment effect. In addition, the tensile strength of 3003-H14 aluminium coil is greater than 140 MPa. And its properties and strength are higher than 1XXX series aluminum alloy. Therefore, it's suitable for processing parts or components that require good formability, high corrosion resistance and weldability.
3003-h14 Aluminum Coil Technical Parameters
| Elements | Si | Fe | Cu | Mn | Zn | Al | |
| Content | 0.6 | 0.7 | 0.05-0.2 | 1.0-1.5 | 0..1 | Remain | |
| Typical Alloy | 3003 Aluminum Coil | ||||||
| Available Temper | F, O, H12, H14, H16, H18, H19, H22, H24, H26, H28, H111, H112, H114 | ||||||
| Thickness (mm) | 0.1-500 | ||||||
| Width (mm) | 20-2650 | ||||||
| Length (mm) | Customize | ||||||
What is aluminum grade 3003 H14?
Aluminum 3003 H14 is commonly used in the manufacturing of sheet metal parts, including panels, ducts, and cabinets. It is also widely used in the packaging industry for the production of food and beverage cans, as well as in the construction industry for the production of roofing and siding materials.
What is equivalent to 3003 H14 aluminum?
Equivalent materials to 3003 H14, such as 3105-H14 and 3004-H14, provide similar mechanical properties and are often used interchangeably in various applications.
Is 3003 H14 aluminum bendable?
It is a good general purpose aluminum with excellent corrosion resistance, and has many uses including trim, building equipment, trailer manufacturing, vehicle components, sign blanks, siding, and cooking utensils among many other things. 3003-H14 aluminum is also easy to bend, form and weld.
What is the difference between 3003 H14 and 6061?
As a comparison, the yield strength of 3003 aluminum H14 temper is typically 17,000 to 24,000 psi, whereas 6061 aluminum yield strength is generally 35,000 to 40,000 psi in the T6 temper.
What is the difference between 3003 H14 and 5052 aluminum?
3003 H14 has an ultimate tensile strength range of 20 – 26 KSI, a yield of 21, an elongation of 8.3%, and a Brinell hardness of 40, while 5052 H32 has an ultimate tensile strength range of 31 – 38 KSI, a yield of 28, an elongation of 12%, and a Brinell hardness of 60.
What is the difference between 3003 H14 and H24?
When it comes to 3003 aluminum sheets, 3003 H14 typically indicates a tensile strength greater than 140MPa, while 3003 H24 represents a product with a strength greater than 240MPa. These distinct properties allow for flexible use cases depending on the specific requirements of the curtain wall application.
Know More About 3003 H14/H24 aluminum sheet for curtain wall
What is the difference between 3003-H14 and 3105 H14?
3105 aluminum has a slight advantage in strength, making it the better choice for applications that require durability in harsh conditions. 3003 aluminum is not as strong, but its more ductile nature gives it the edge in applications that require forming. Which one is better depends on the needs of your application.
Is 3003 cheaper than 5052?
ANS: 3003 is usually more cost-effective in industrial projects. Its usually costs 15% to 20% less than 5052. For example, 3003 aluminium sheet prices can differ from $2,100 to $2,500 per ton while 5052 can be 15% to 20% higher.
Is 3003 aluminum marine grade?
Marine-grade alloy, commonly used in boats and tankers. Heat-treatable, structural alloy, less formable but very strong.
3003-H14 5052-H32 Aluminium Coil Detailed Photos
3003-H14 5052-H32 Aluminium Coil Quality Control
3003-H14 5052-H32 Aluminium Coil Packing
