1 Series Aluminum Plate and Sheet: Grades and Applications

Dec 31, 2025

Leave a message

Aluminum plate and sheet in the 1xxx series are classified as unalloyed or commercially pure, with a minimum aluminum content of 99.00 percent. Grades 1050, 1060, 1070 and 1100 differ mainly in purity and in the small copper addition found in 1100. They are specified under ASTM B209 for sheet and plate and under EN 573-3 for composition, while GB/T 3880 covers the equivalent domestic grades.

The family is chosen wherever electrical or thermal performance, formability and corrosion resistance matter more than structural strength. It also forms the base stock from which many packaging foils and fin stocks are rolled.

What Defines the 1xxx Sheet Family

The defining feature of the 1xxx series is a controlled minimum aluminum content rather than a deliberate alloying addition. Grade 1050 contains 99.50 percent aluminum, 1060 contains 99.60 percent, and 1070 reaches 99.70 percent, which is the highest purity normally produced in commercial sheet. Grade 1100 is the exception, carrying about 0.12 percent copper that raises strength slightly without spoiling formability.

All four grades share a face-centered cubic structure, low density near 2.70 grams per cubic centimeter and no response to precipitation hardening. Their strength therefore comes from strain hardening and from the amount of cold reduction left in the finished product.

Grade by Grade Comparison

Grade 1050 is used for electrical conductors, heat sinks, chemical equipment and general sheet metal work. Grade 1060 is a common choice for deep-drawn cookware, foil stock and lighting reflectors because it combines high purity with good drawing behavior. Grade 1070 is selected where maximum conductivity and reflectivity are required, such as capacitor foil and specialized reflectors.

Grade 1100 adds copper for a modest strength increase and is widely used for signage, nameplates, spinning and drawn parts. It also machines a little better than the fully pure grades, although it is never considered a high-strength alloy.

Mechanical and Physical Properties

In the H14 temper, 1050 sheet typically shows a tensile strength near 100 MPa with elongation above 20 percent, while 1100-H14 reaches roughly 125 MPa. Annealed O temper drops strength to about 70 MPa for 1050 and 90 MPa for 1100 while maximizing elongation for severe forming.

Electrical conductivity of the pure grades falls between 59 and 62 percent of the International Annealed Copper Standard, and thermal conductivity is around 230 W per meter kelvin. Density stays close to 2.70 grams per cubic centimeter, roughly one third that of steel, so weight savings are substantial in transport and electrical hardware.

Thickness, Temper and Application Range

Sheet is generally supplied from 0.2 mm to 6.0 mm and plate from 6.0 mm upward, with widths commonly reaching 1500 mm to 2000 mm in coil and cut-to-length form. Tempers include O for maximum ductility, H12 and H14 for quarter-hard forming, H16 and H18 for higher strength, and H22 to H24 for partially annealed strain-hardened sheet.

Typical applications include bus bar and conductor stock, transformer windings, heat exchanger fins, cookware, reflective panels, nameplates and deep-drawn containers. Selection normally balances required conductivity, forming severity and the strength needed to resist handling damage.

Frequently Asked Questions

Q: Can 1xxx aluminum be heat treated?
No. The 1xxx series is non-heat-treatable, so strength is controlled only by cold work and annealing. Tempers such as H14, H18 and H24 describe the amount of strain hardening rather than a thermal treatment.

Q: Which grade has the highest conductivity?
Grade 1070 is normally the highest purity commercial grade at about 99.70 percent aluminum, so it offers the best electrical and thermal conductivity and the highest reflectivity among standard 1xxx sheet products.

Q: What is the difference between 1050 and 1100?
1050 is 99.50 percent pure and is chosen for conductivity and forming, while 1100 contains about 0.12 percent copper that raises tensile strength slightly and improves machinability at a small cost in conductivity.

Q: Which standards cover 1xxx sheet and plate?
ASTM B209 defines the mechanical requirements for aluminum sheet and plate, EN 573-3 defines chemical composition and designation, and GB/T 3880 covers equivalent domestic sheet and plate specifications.

Q: Is 1xxx aluminum suitable for marine use?
It resists atmospheric and fresh water corrosion well, but it is not designed for sustained seawater structural service. For marine plate, higher-magnesium alloys such as 5052 and 5083 are the usual selection.