Henan Gnee New Material Co., Ltd. is one of the most reliable manufacturers and suppliers of 6061-T651 Aluminum Round Bar in China. With abundant experience, we warmly welcome you to wholesale high quality 6061-T651 Aluminum Round Bar in stock here from our factory. Good service and reasonable price are available.
What is 6061-T651 Aluminum Round Bar
6061 is a heat-treatable wrought aluminum-magnesium-silicon alloy in the 6xxx series. Its primary strengthening phase is magnesium silicide (Mg2Si), which precipitates as fine particles during artificial aging to raise strength. The alloy balances moderate-to-high strength with good corrosion resistance, weldability and machinability, which is why it is the most widely used heat-treatable aluminum grade across aerospace, automotive, marine and general engineering.
The T651 temper describes a specific processing route: solution heat treatment, quenching, a controlled stretch of 1–3% to relieve internal stress, and artificial aging. For extruded stock the equivalent stress-relieved temper is written T6511. The stretch is what makes T651 different from plain T6 - strength is essentially unchanged, but residual stress is released, so the bar resists warping and twisting when you machine away material.
A round bar (or rod) is solid cylindrical stock supplied either cold-finished (drawn to tight diameter and straightness per ASTM B211) or extruded (per ASTM B221), then cut to length. It is the starting material for shafts, pins, bushings, fasteners, mold plates, jigs and countless turned or milled components.

Chemical Composition
The registered composition limits for 6061 are identical across ASTM B211 (bar/rod/wire), ASTM B221 (extruded bar) and EN 573-3 (EN AW-6061), so a single certificate satisfies both American and European chemical requirements.
| Element | Min % | Max % | Role / Function |
|---|---|---|---|
| Silicon (Si) | 0.40 | 0.80 | Combines with Mg to form the Mg2Si strengthening phase |
| Iron (Fe) | - | 0.70 | Impurity; controlled to limit hard intermetallics that dull cutting tools |
| Copper (Cu) | 0.15 | 0.40 | Adds solid-solution strengthening and accelerates aging |
| Manganese (Mn) | - | 0.15 | Grain refinement; counters Fe intermetallic effects |
| Magnesium (Mg) | 0.80 | 1.20 | Primary alloying element; forms Mg2Si with silicon |
| Chromium (Cr) | 0.04 | 0.35 | Controls grain growth; improves corrosion resistance |
| Zinc (Zn) | - | 0.25 | Residual impurity; limited to preserve corrosion behavior |
| Titanium (Ti) | - | 0.15 | Grain refiner during casting |
| Others, each | - | 0.05 | Individual trace element limit |
| Others, total | - | 0.15 | Combined trace element limit |
| Aluminum (Al) | Remainder (approx. 95.8–98.6%) | Base matrix | |
Source: ASTM B211 / ASTM B221 / EN 573-3 registered limits for 6061 (EN AW-6061).
Mechanical Properties
Strength is set by temper. The values below are typical for bar and rod; the guaranteed minimums in ASTM B211 for 6061-T6/T651 are 290 MPa (42 ksi) tensile and 240 MPa (35 ksi) yield, with actual certified heats commonly testing higher. Elongation steps down as diameter increases, so a heavy section does not carry the same guarantee as a small drawn bar.
| Temper | UTS MPa (ksi) | Yield 0.2% MPa (ksi) | Elongation % | Hardness (HBW) |
|---|---|---|---|---|
| O (annealed) | ≤ 150 (22) | ≤ 85 (12) | 15–25 | 30 |
| T4 | 180–240 (26–35) | 110–150 (16–22) | 16–22 | 65 |
| T6 | 290–330 (42–48) | 240–280 (35–41) | 8–12 | 95 |
| T651 | 290–330 (42–48) | 240–280 (35–41) | 8–12 | 95 |
| T6511 | 290–330 (42–48) | 240–280 (35–41) | 8–12 | 95 |
Source: ASTM B211 minimums (290 MPa / 240 MPa for T6, T651) with typical ranges per ASM and supplier datasheets. Elongation depends on diameter and test direction.
Typical reference values for 6061-T651: tensile ≈ 310 MPa (45 ksi), yield ≈ 276 MPa (40 ksi), elongation ≈ 12%, hardness ≈ 95 HB, shear strength ≈ 207 MPa (30 ksi), fatigue strength ≈ 97 MPa (14 ksi) at 5×108 cycles.
Physical & Thermal Properties
| Property | Value (Metric) | Value (Imperial) |
|---|---|---|
| Density | 2.70 g/cm³ | 0.0975 lb/in³ |
| Melting range | 582–652 °C | 1080–1205 °F |
| Modulus of elasticity | 68.9 GPa | 10,000 ksi |
| Thermal conductivity (T6) | 167 W/m·K | 96.5 BTU/hr·ft·°F |
| Electrical conductivity (T6) | ≈ 43% IACS | - |
| Electrical resistivity | 3.99 µΩ·cm | - |
| Coefficient of thermal expansion (20–100 °C) | 23.6 µm/m·°C | 13.1 µin/in·°F |
| Specific heat capacity | 896 J/kg·K | 0.214 BTU/lb·°F |
| Poisson's ratio | 0.33 | 0.33 |
Source: ASM Handbook and 6061-T6/T651 datasheets. Thermal and electrical values are for the T6 temper at 20–25 °C.
6061-T651 Aluminum Round Bar Specifications & Tolerances
| Item | Specification |
|---|---|
| Alloy / temper | 6061-T651 (T6511 extruded equivalent); T6, T4, O on request |
| Material standard | ASTM B211 (cold-finished bar/rod/wire), ASTM B221 (extruded bar); AMS 4027, AMS-QQ-A-225/8, ISO 6362, EN 754-2 |
| Shape | Round bar / rod (square and hex on request) |
| Diameter range | 3–300 mm (0.125–12 in); larger extruded sizes to 400 mm available |
| Length | 1000–6000 mm (approx. 3–20 ft) standard; cut-to-length available |
| Diameter tolerance | Cold-finished ±0.0015–0.006 in by size (h8/h9); precision-ground h6/h7 available |
| Straightness | Cold-finished 0.025 in/ft; precision-ground ≤ 0.5 mm/m |
| Surface |
Mill, cold-drawn, or precision ground (Ra ≤ 0.8–1.6 µm) |
The table below shows typical cold-finished 6061-T651 diameter tolerances for common sizes; extruded stock carries wider tolerances.
| Diameter (in) | Diameter (mm) | Cold-finished tolerance (in) |
|---|---|---|
| 1/4 | 6.35 | ±0.0015 |
| 3/8 | 9.53 | ±0.0015 |
| 1/2 | 12.7 | ±0.0015 |
| 5/8 | 15.88 | ±0.002 |
| 3/4 | 19.05 | ±0.002 |
| 1 | 25.4 | ±0.002 |
| 1-1/4 | 31.75 | ±0.0025 |
| 1-1/2 | 38.1 | ±0.0025 |
| 2 | 50.8 | ±0.004 |
| 3 | 76.2 | ±0.006 |
Source: ASTM B211 cold-finished bar diameter tolerances (representative). Confirm exact tolerance and straightness against your order.
Heat Treatment & Temper Guide
6061 reaches its strength through three stages, summarized for the common tempers below.
Solution heat treatment - heat to approximately 530 ±5 °C (985 °F) and hold until the Mg2Si and alloying elements dissolve into the aluminum matrix, then quench rapidly (usually water) to freeze the supersaturated solid solution.
Stress relief (T651) - stretch 1–3% to relax the internal stress locked in by quenching. This is the step that separates T651 from T6 and gives the bar its dimensional stability.
Artificial aging - reheat to roughly 160–175 °C (320–350 °F) for 8–18 hours (a common cycle is 175 °C for 8 h) to precipitate fine Mg2Si particles that raise strength to the T6 level.
| Temper | Process | Key characteristic / typical use |
|---|---|---|
| O | Annealed | Softest; maximum formability for bending or deep drawing |
| T4 | Solution treated + naturally aged | Moderate strength, good formability; can be aged to T6 after forming |
| T6 | Solution treated + artificially aged | Full strength; general structural and machined parts |
| T651 | T6 + stretched 1–3% for stress relief | Same strength, dimensionally stable; industry standard for CNC machining |
| T6511 | Stress-relieved extruded (stretch or compress) | Extrusion equivalent of T651 |
Source: ASM Handbook, Volume 4 (Heat Treating of Aluminum Alloys) and AMS 2770/2772 practices. Exact soak times and temperatures vary with section thickness and are confirmed on the mill certificate.
Equivalent Designations
| Standard | Designation | Note |
|---|---|---|
| AA (Aluminum Association) | 6061 | Primary North American designation |
| UNS | A96061 | ASTM/SAE unified numbering |
| EN (European) | EN AW-6061 / EN AW-AlMg1SiCu | EN 573-3 |
| DIN (German) | 3.3211 / AlMgSi1Cu | DIN 1725-1 material number |
| JIS (Japanese) | A6061 | JIS H4000 / H4040 |
| GB (Chinese) | 6061 (formerly LD30) | GB/T 3190 |
| ISO | AW-6061 / AlMg1SiCu | ISO 209-1 |
| SAE AMS | AMS 4027 (T651 bar) | AMS-QQ-A-225/8 cold-finished |
Source: ASTM B211/B221, EN 573-3, ISO 209-1, JIS H4000/H4040, GB/T 3190, SAE AMS 4027.
Corrosion Resistance
6061 has good corrosion resistance for a heat-treatable alloy and is rated "good" for general use. Behavior across five environments:
Atmospheric - good resistance; the natural oxide film protects the surface in normal indoor and outdoor exposure.
Marine - acceptable for above-water and splash-zone hardware, but 6061 is not a substitute for 5xxx alloys in continuously submerged seawater service; specify anodizing for coastal exposure.
Galvanic - aluminum is anodic to steel and copper, so isolate 6061 from dissimilar metals with non-conductive washers, coatings or joint compounds to prevent galvanic attack.
Stress corrosion cracking (SCC) - low susceptibility in the T6/T651 temper for most sections; the chromium addition and controlled aging reduce SCC risk in service.
Surface finish - anodizing (Type II, or hard-coat Type III) and chromate conversion coatings measurably improve corrosion and wear resistance for demanding environments.
Fabrication
Welding - 6061 welds well by GTAW (TIG) and GMAW (MIG). Use ER4043 filler for lower crack sensitivity and smoother feeding, or ER5356 for higher joint strength and better anodized color match. The heat-affected zone softens after welding, so a welded assembly will not retain full T6/T651 strength locally.
Machining - 6061-T651 is rated "good" (Class B) for machinability. It turns, mills, drills and taps cleanly with carbide tooling at 150–300 m/min cutting speeds, and the stress-relieved microstructure keeps parts flat during high-removal operations.
Formability - poor in the T6/T651 temper. For bending or forming, specify O or T4 stock and age to T6 after forming.
Surface Finishes
| Finish | Description | Typical use |
|---|---|---|
| Mill / as-drawn | As-supplied surface, economical | General structural and machined parts |
| Anodized (Type II) | Sulfuric anodizing; clear or colored | Corrosion protection, appearance, color coding |
| Hard anodized (Type III) | Thick, wear-resistant oxide layer | Sliding or abrasive-contact components |
| Precision ground | Centerless ground, Ra ≤ 0.8 µm | Shafts, pins, bearing fits, Swiss-type lathe stock |
| Polished / brushed | Mechanical polishing or satin finish | Decorative and architectural parts |
Applications
| Industry | Use | Why 6061-T651 |
|---|---|---|
| Aerospace | Brackets, fittings, structural machined parts | Strength-to-weight ratio with dimensional stability |
| Automotive | Drive shafts, suspension components, hubs | Good strength, weldability and corrosion resistance |
| Marine | Fittings, frames, deck hardware | Corrosion resistance with machinability |
| Precision machining / CNC | Mold bases, jigs, fixtures, locating pins | T651 stress relief prevents warp during cutting |
| Automation equipment | Robot arms, frame members, shafts | Stable, tight-tolerance machined parts |
| Semiconductor / electronics | Precision components, thermal plates | Dimensional stability and good thermal conductivity |
| Sporting goods | Bicycle and motorcycle components | Light weight with good strength and finish |
| Hydraulic / pneumatic | Valve bodies, connectors, manifolds | Machinability and moderate pressure capability |

6061-T651 vs Other Aluminum Bars
| Property (data basis) | 6061-T651 | 7075-T651 | 2024-T351 | 6063-T5 | 6082-T6 |
|---|---|---|---|---|---|
| UTS, typical | 310 MPa (45 ksi) | 570 MPa (83 ksi) | 470 MPa (68 ksi) | 190 MPa (28 ksi) | 310 MPa (45 ksi) |
| Yield 0.2%, typical | 276 MPa (40 ksi) | 503 MPa (73 ksi) | 325 MPa (47 ksi) | 145 MPa (21 ksi) | 260 MPa (38 ksi) |
| Elongation, typical | 12% | 11% | 20% | 12% | 10% |
| Density | 2.70 g/cm³ | 2.81 g/cm³ | 2.78 g/cm³ | 2.70 g/cm³ | 2.71 g/cm³ |
| Fusion welding (joint strength vs. parent) | 65–75% with ER4043 / ER5356 | not recommended - solidification hot-cracking | not recommended - solidification hot-cracking | 70–80% with ER4043 / ER5356 | 65–75% with ER4043 / ER5356 |
| Suggested cutting speed, m/min (carbide tooling) | 150–300 | 180–400 | 200–450 | 100–200 | 150–300 |
| Indicative relative cost (6061 bar = 1.0, market-dependent) | 1.0 (reference) | approx. 1.7–2.0 | approx. 1.4–1.7 | approx. 0.8–0.9 | approx. 1.0 |
| Primary alloying system | Al-Mg-Si (heat-treatable) | Al-Zn-Mg-Cu (heat-treatable) | Al-Cu-Mg (heat-treatable) | Al-Mg-Si (heat-treatable) | Al-Mg-Si (heat-treatable) |
Why Choose GNEE
18 years of export experience - established aluminum manufacturer and exporter supplying bar, rod, plate and profiles to industrial buyers worldwide.
Flexible MOQ & lead time - from small trial orders to full container volumes, with a typical lead time of 15–30 days depending on diameter, quantity and finish.
Custom cutting & tolerances - cut-to-length, chamfered ends and precision-ground diameters to your drawing or tolerance grade.
Full mill test certificate - EN 10204 3.1 MTC with every lot, covering chemical composition and mechanical properties; third-party inspection on request.
Export-grade packaging - moisture- and scratch-resistant wrapping suitable for sea freight, with markings per your specification.

Send your bar spec for a firm offer
FAQ
What is the difference between 6061-T6 and 6061-T651? - Both are solution heat-treated and artificially aged to the same strength. T651 adds a controlled 1–3% stretch that relieves quench stress, so the bar warps far less during machining. Choose T651 for precision CNC work; T6 is the lower-cost general-purpose option.
Can 6061-T651 bar be welded? - Yes, by TIG or MIG. Use ER4043 for easier feeding and lower crack risk, or ER5356 for higher joint strength and better anodized color match. The weld zone softens after welding, so full T6 strength is not retained locally.
Does 6061-T651 rust? - No. It forms a protective oxide layer and does not rust like steel. For marine or coastal exposure, add anodizing or a conversion coating.
What tolerances and straightness apply? - Cold-finished 6061-T651 is normally ±0.0015–0.006 in on diameter (tighter h6/h7 ground tolerances available) and 0.025 in/ft straightness; precision-ground rod can hold 0.5 mm/m.
Is a material test certificate provided? - Yes, an EN 10204 3.1 MTC ships with every lot and covers both chemistry and the T651 mechanical properties.
What is the MOQ and lead time? - MOQ is flexible, from small trial orders to full containers. Lead time is typically 15–30 days and is confirmed at quotation.
Email your size list - get a price today
Hot Tags: 6061-T651 Aluminum Round Bar, China 6061-T651 Aluminum Round Bar manufacturers, suppliers, factory, Industrial Aluminum Round Rods, 1060 Aluminum Round Bar, polished aluminum rod 6063




