6061 T6 Aluminum Rectangular Tube

6061 T6 Aluminum Rectangular Tube

GNEE is an aluminum manufacturer with 18 years of export experience, supplying ASTM B221 / EN 755 extruded aluminum rectangular tube in 6061-T6 and other tempers to distributors, machine builders, and engineering contractors in more than 100 countries. A rectangular hollow section gives a frame member far higher bending and torsional stiffness per kilogram than a solid bar of the same outer size, which is why it is the default choice for machine bases, guards, and automation frames.
Send Inquiry
Chat Now
Description

Henan Gnee New Material Co., Ltd. is one of the most reliable manufacturers and suppliers of 6061 T6 Aluminum Rectangular Tube in China. With abundant experience, we warmly welcome you to wholesale high quality 6061 T6 Aluminum Rectangular Tube in stock here from our factory. Good service and reasonable price are available.

 

The risk if the section is not controlled: when a rectangular tube ships with a bowed side (over 2 mm in 3 m), a twisted corner, or a wall that is 0.02″ thin on one face, your assembly does not line up. Bolting holes drift, the panel sits proud, and the whole batch goes back for re-cutting-or worse, the frame carries a load it was never dimensioned for and deflects in service. We hold straightness, squareness, and wall tolerance to the ordered spec and confirm every lot on the mill test certificate before it leaves the plant. Contact now to discuss sizes, the wall, and the right temper for your frame.

 

What is 6061-T6 Aluminum Rectangular Tube

A 6061-T6 aluminum rectangular tube is a hollow, extruded profile with a rectangular outer cross-section-specified by outside width × outside height × wall thickness × length. The alloy belongs to the 6xxx series (Al-Mg-Si), precipitation-hardened. The T6 temper means solution heat-treated and then artificially aged to reach peak strength. Compared with 6063, 6061 carries roughly 30% higher strength at a small cost in surface finish and extrudability; compared with 6082, it is slightly easier to weld and machine. The hollow shape is the point: for a given outer envelope, a tube resists bending and twisting far better than a solid bar, so you build a rigid, light frame without over-weighting the structure.

 

Typical use cases are structural framing, machine guards and enclosures, automation equipment bases, trailer and rack sub-frames, marine topside handrails, solar mounting rails, display and exhibition structures, and architectural mullions. When the section is large or will be heavily machined after delivery, we supply 6061-T6511 (stress-relieved) to keep it from moving during cutting.

 

6061-T6 Aluminum Rectangular Tube

 

Chemical Composition

Composition follows the Aluminum Association limits for AA 6061 (ASTM B221 / EN 573-3). Values are weight percent.

Element Min % Max % Role / Function
Aluminum (Al) - Remainder Base metal; provides lightweight and corrosion resistance.
Silicon (Si) 0.40 0.80 Forms Mg₂Si with Mg; drives precipitation hardening and extrudability.
Magnesium (Mg) 0.80 1.20 Primary strengthening element with Si; improves corrosion behavior.
Copper (Cu) 0.15 0.40 Raises strength and hardenability; slightly lowers SCC resistance.
Manganese (Mn) - 0.15 Controls grain structure and recrystallization.
Chromium (Cr) 0.04 0.35 Controls grain growth and improves toughness and SCC resistance.
Iron (Fe) - 0.70 Impurity; kept low to protect surface and anodizing response.
Zinc (Zn) - 0.25 Impurity; limited to avoid hot cracking.
Titanium (Ti) - 0.15 Grain refiner.
Others each / total - 0.05 / 0.15 Trace impurity limits per ASTM B221.

 

Mechanical Properties

Values are typical for extruded 6061 per ASTM B221; actual figures appear on the mill test certificate and vary slightly with section thickness. T6 is the peak-strength temper; O is fully soft; T6511 adds stretch stress relief.

Temper UTS MPa Yield MPa Elong % Hardness HB
O (annealed) 90–130 40–70 15–25 25–30
T4 180–240 100–150 18–22 65–70
T6 290–330 240–280 10–17 90–95
T6511 (stress-relieved) 290–330 240–280 10–17 90–95

Typical T6 shear strength is about 207 MPa and the rotating-beam fatigue limit is about 96.5 MPa. In practice, specify the tube by T6 minimums: 310 MPa UTS / 276 MPa yield are the common catalog values, with elongation 8% at wall ≤6.35 mm.

 

Physical & Thermal Properties

Property Metric Imperial
Density 2.70 g/cm³ 0.0975 lb/in³
Melting range 582–652°C 1080–1205°F
Elastic modulus 68.9 GPa 10.0×10⁰ ksi
Thermal conductivity (T6) 152–167 W/m·K ~970–1160 BTU·in/(hr·ft²·°F)
Electrical conductivity (T6) 43% IACS 25 MS/m
CTE (20–100°C) 23.6 µm/m·K 13.1 µin/in·°F
Poisson's ratio 0.33 0.33
Specific heat 0.896 J/g·K 0.214 BTU/lb·°F

 

6061-T6 Aluminum Rectangular Tube Specifications Table

Parameter Typical range / note
Shape Rectangular hollow section (RHS)
Alloy & temper 6061-T6, also T6511, O, and T4 on request
Standards ASTM B221 (extruded), ASTM B241 (seamless extruded), EN 755, AMS 4117, AMS-QQ-A-200/8
Outside width × height 12.7 × 25.4 mm (0.5″ × 1″) up to ~200 × 300 mm
Wall thickness 1.6–6.35 mm (0.062″–0.250″); thicker on request
Length Up to 12 m (39 ft) random or cut-to-length
Straightness ≤ 1 mm per 1000 mm typical, per ASTM B221
Wall tolerance ±10% of nominal wall, per ASTM B221
Finish Mill finish as standard; anodized / powder on request
Design load rating depends on span, support, and weld; supply load case for rating

 

6061-T6 Aluminum Rectangular Tube for sale

 

Heat Treatment & Temper Guide

6061 is heat-treatable, so the T6 cycle in the template applies directly. For extruded rectangular tubes, the production route is:

Solution heat treatment: 530 ± 5°C, hold, then water quench to lock Mg₂Si in solid solution.

Artificial aging: 175 ± 5°C for 8 hours, air-cooled, to precipitate the hardening phase.

T6511: after quenching, the section is stretched 1–3% to relieve residual stress, then aged. This is the right call for large or machined-after-delivery frames because it stops the tube from bowing when you cut it.

Note: aging below 175°C (e.g., T5-style air cooling) does not reach T6 strength; if you need peak properties, order T6 or T6511 explicitly rather than assuming an extruded-and-air-cooled section is T6.

 

Equivalent Designations

AA UNS EN DIN JIS GB ISO
6061 A96061 EN AW-6061 (AlMg1SiCu) 3.3211 A6061 (JIS H4000) 6061 (GB/T 3190) AW-6061

 

Corrosion Resistance

Atmospheric: Good in rural and urban air; a thin oxide film protects the base. In industrial/coastal atmospheres, anodizing or powder coating extends service life.

Marine: Adequate for topside (above-water) structures-handrails, frames, and supports. For continuous splash or submerged use, specify 5083 or add coating; 6061 is not the first choice for submerged marine.

Galvanic: Aluminum is anodic to steel, copper, and stainless. Isolate with dielectric washers or use a compatible filler; direct contact with carbon steel in wet conditions drives rapid pitting of the tube.

Stress-corrosion cracking (SCC): Low risk in T6 for standard sections. The short-transverse direction is the sensitive one; avoid heavy cold forming of thick walls after aging. T6511 lowers residual stress further.

Finished protection: Mill finish is sufficient for dry indoor frames. Anodize (Type II/III) or PVDF/powder for outdoor and architectural exposure. [To be confirmed] for salt-spray hours beyond 1000 h on thick anodize.

 

Fabrication

Welding. 6061-T6 welds well by GTAW (TIG) and GMAW (MIG). Use ER4043 for general structural joints (good flow, lower color match) or ER5356 where you need higher joint strength and a closer anodizing color. Expect the heat-affected zone to soften to roughly T4 strength; if the frame must keep full T6 properties at the weld, plan for post-weld reheat-treat or design to the welded strength. Avoid copper-based fillers.

Machining. Good in T6 with sharp carbide tools and flood coolant. The hollow section needs proper clamping to avoid crushing the wall; use soft jaws or a purpose-built fixture. T6511 is preferred for tight-tolerance CNC work because residual stress is already relieved.

Formability. Limited in T6-bend radii should be 2.5–3.5× wall to avoid tension-side cracking. For cold bending or forming, order 6061-O or T4 and age after forming. Cutting, drilling, tapping, and CNC milling are routine in the as-supplied T6 condition.

 

Surface Finishes

Finish Process When to use
Mill finish As-extruded, visible die lines Structural, indoor, cost-sensitive frames
Anodized (Type II/III) Sulfuric/hard anodize, 5–50 µm Outdoor, wear, architectural; clear or RAL color
Powder coated Electrostatic RAL color Visible structures, brand color, UV resistance
PVDF-coated Fluorocarbon, 70% PVDF Long-life architectural façades
Brushed / polished Mechanical satin or mirror Decorative and display structures

 

Applications

Machine framing & guards: work-cell frames, safety guards, and enclosures-T6 stiffness at one-third steel weight, easy to bolt and weld.

Automation equipment bases: robot pedestals, conveyor supports, gantry beams-T6511 holds tolerance after machining.

Trailers & racks: sub-frames, roof racks, and ladder racks-high strength-to-weight, weldable on-site.

Marine topside: handrails, T-tops, and cabin frames above the waterline-corrosion-resistant, light.

Solar mounting: rail and torque-tube structures-straight, consistent, and anodizable for 20+ years of outdoor life.

Display & exhibition: booth frames, shelving, sign structures-clean mill or anodized look, fast assembly.

Architectural: mullions, canopies, balustrade posts-pairs with curtain-wall systems.

General fabrication: jigs, fixtures, cart frames, and OEM sub-assemblies.

 

Marine topside

 

6061 vs. Other Aluminum Alloy Comparison

Alloy (temper) UTS MPa Yield MPa Density g/cm³ Weldability Best use
6061-T6 290–330 240–280 2.70 Very good (ER4043/ER5356) Structural frames, welded assemblies
6063-T5/T6 190–240 140–200 2.70 Excellent Architectural, window/door, décor
6082-T6 290–340 250–300 2.70 Good (some HAZ loss) Heavy structural bridges
5083-O/H111 275–350 110–145 2.66 Good (ER5183) Marine, welded plate/tube
7075-T6 510–570 430–505 2.81 Poor (crack-sensitive) Aerospace, high-strength non-welded

 

Why Choose GNEE

GNEE supplies aluminum extruded tube with documented traceability and 18 years of export experience serving distributors, machine builders, and EPC contractors across more than 100 countries. What you get on every order:

Mill Test Certificate with every lot. Chemistry, tensile, and hardness are recorded per heat and shipped with the material-not offered as an extra. You can verify the grade before you cut.

Custom section and cut-to-length. Standard widths/heights/walls are stocked; non-standard rectangles and tapers are quoted from your drawing. Lengths are cut to your requirement instead of forcing you to buy random 6 m bars.

Lead time 15–30 days. Stock sizes ship inside the short end; made-to-order extrusions run on a published schedule. We confirm the date at order, not after.

Straightness and squareness held to spec. Every tube is checked for bow, twist, and wall variation before packing, because a 2 mm bow is what makes your frame not line up. Out-of-spec lots are rejected at our gate, not yours.

Protected packaging for export. Bundled, strapped, and wrapped against moisture and edge damage; seaworthy crating on request so the section arrives square, not dented.

 

6061 T6 SEAMLESS PIPE Loading photo 30

 

Quality Control

Risk we control: a rectangular tube that leaves the plant bowed, twisted, or with a thin wall will not assemble in your jig and may carry a load it was never dimensioned for. Our incoming and final checks cover:

Check Method / standard Acceptance
Dimensions & straightness Calipers, straightedge, square per ASTM B221 Wall ±10%, straightness ≤1 mm/1000 mm
Hardness Webster / Brinell (ASTM B10) T6 range 90–95 HB
Tensile Tensile test per ASTM B557 on sample UTS ≥290 MPa, Yield ≥240 MPa
Chemistry Spectrometer PMI (OES) Within AA 6061 limits
Surface & MTC Visual + mill cert review No deep die lines, cert matches heat

 

Quality Control

 

Every lot ships with its MTC attached. If a check fails, the lot is isolated and replaced before your container is sealed. Contact now for a sample cert or to book an inspection.

Contact Our Engineers Today

FAQ

Q1: Can 6061-T6 rectangular tube keep full T6 strength after welding?
A: No. The heat-affected zone softens to roughly T4. Design the joint to welded strength, or plan post-weld reheat treatment if the application demands full T6 at the weld.

Q2: What is the difference between T6 and T6511 for a frame?
A: Same strength; T6511 is stretched 1–3% after quenching to relieve residual stress, so it stays straight and stable when you machine it. Choose T6511 for large or precision-machined sections.

Q3: What wall thickness and size range do you stock?
A: Common stock runs 0.5″×1″ up to 4″×8″ outer, wall 0.062″–0.250″. Larger rectangles and thicker walls are made to order; confirm the exact envelope with us.

Q4: Is 6061-T6 good for marine use?
A: For topside (above-water) structures-handrails, frames-yes, with anodizing or coating. For submerged or constant splash service, 5083 is the better choice.

Q5: Do you supply mill test certificates and cut-to-length?
A: Yes. Every lot ships with an MTC (chemistry, tensile, hardness per heat), and we cut to your length instead of shipping random long bars.

 

Ready to specify your 6061-T6 rectangular tube? Send your width × height × wall × length, temper, and finish, and we will return a quote with MTC and current lead time.

Send an Inquiry Now

 

GNEE aluminum

Hot Tags: 6061 T6 Aluminum Rectangular Tube, China 6061 T6 Aluminum Rectangular Tube manufacturers, suppliers, factory, 6061 T6 Aluminum Rectangular Tube